• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Chapter 18 Surface Preservation - 14325_513
ZONE INSPECTION - 14325_515

Basic Military Requirements (BMR) Revised Edition
Page Navigation
  494    495    496    497    498  499  500    501    502    503    504  
worse, they might clog up dewatering equipment if the space were flooded. SWEEPERS “Sweepers”  is  piped  shortly  after  reveille,  before the end of the regular working day, and at other times as scheduled.  At  these  times,  all  persons  assigned  as sweepers  draw  their  gear  and  sweep  and  swab  down their assigned areas. All trash and dirt are picked up in a dustpan and placed in a trash receptacle. NOTE If dirt is swept over the side, the wind may blow it back on board or the dirt may stick to the side of  the  ship.  In  either  case,  additional  work  is necessary to clean the ship. At this time you should empty all butt kits (make sure no butts are still burning) and trash receptacles as instructed. Never dump trash or garbage over the side of the  ship  without  first  obtaining  permission  from  the officer of the deck. At times, all trash must be kept in a safe  area  aboard  the  ship  until  it  can  be  properly removed. CLEANING PROCESS Dirt, soil, and contamination all describe the same thing—a foreign material on a surface where it is not wanted.  Soil  includes  grease,  oil,  tarnish,  rust,  food residue,  and  stains.  Most  exposed  surfaces  that  have been  soiled  may  be  cleaned  with  the  proper  use  of cleaning agents. Detergents  are  materials  that  have  the  ability  to remove contamination and soil. There are other ways of cleaning   besides   using   detergents   or   cleaning compounds.   These   include   purely   mechanical processes,  such  as  removing  rust  from  steel  by  sand- blasting  or  cleaning  decks  by  sweeping.  For  many cleaning  problems,  chipping,  sweeping,  sanding,  or brushing  may  be  needed.  However,  when  detergent compounds are coupled with the mechanical action, a cleaner surface is usually produced with less time and work. The  steps  used  in  most  detergent  cleaning operations are as follows: 1.   Wetting—The soil and the surface of the object being  cleaned  must  be  wetted.  If  the  surface  is  not wetted properly, cleaning results will be poor. Contrary to  popular  belief,  water  has  very  poor  wetting properties. Its wetting ability, and therefore its cleaning ability, is improved by adding other materials, such as soap or synthetic detergents. Adding soap or synthetic detergents cause the water to flow into tiny crevices and around small particles of soil. 2.   Scrubbing—Dirt is loosened by the mechanical action  of  rubbing  or  scrubbing.  For  example,  oil droplets are emulsified; that is, they are coated with a thin film of soap and prevented from recombining, and then  they  rise  to  the  surface.  In  a  somewhat  similar manner, solid particles are suspended in solution. 3.   Rinsing—Rinsing  is  very  important.  Rinsing removes loosened dirt from the surface along with the cleaning material. FIELD DAY Field day is cleaning day. Periodically, a field day is held. All hands “turn to” and thoroughly clean the ship inside and out, usually in preparation for an inspection. Fixtures and areas that sometimes are neglected during regular sweepdowns (overhead cables, piping, corners, spaces  behind  and  under  equipment,  and  so  on)  are cleaned.  Bulkheads,  decks,  ladders,  and  all  other accessible  areas  are  scrubbed.  Knife  edges  and  door gaskets are checked; any paint, oil, or other substances are removed; all brightwork is shined; and clean linen is placed on each bunk. Field days improve the appearance and  sanitary  condition  of  the  ship,  aid  in  the preservation  of  the  ship  by  extending  paint  life,  and reduce the dirt intake caused by operating equipment. Because of weather conditions, there are many days at sea when the ship’s topside areas can’t be cleaned. At the  first  opportunity,  all  topside  surfaces  are  cleaned with  freshwater  and  inspected  for  signs  of  rust  and corrosion. If such signs are discovered, you should tend to the area immediately. A little work at that time will save you a lot of work later. 18-2 Student Notes:







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.